PSU-50 - Power Supply for 50W Tube Power Amp


In Stock
Product Code:


PSU-50 is a super-low-noise power supply that supports a 50W tube power amplifier, or a 25+25W stereo power amp, along with tube preamplifiers and auxiliary circuits. PSU-50 ideally matches London Power's tube power amp kits, such as PA66-25 and PA66-976

Tube power amplifiers require various voltages for the plate circuit, bias and heaters. PSU-50 provides an integrated power supply solution that is compact while providing extremely clean support for tube audio circuitry. These supplies are so good we use them in our own amplifiers!

The PCB accommodates wiring for world-wide mains compatibility using an offboard 115/230V range switch. The board itself supports the following:

  • dual mains fuses
  • plate supply 430Vdc - 500mA
  • active hum filtering for high-voltage plate supply
  • bias supply for fixed-biasing
  • 6V/12V London Power heater system
  • supports four octal power tubes plus 20x 12A_7 preamp tubes
  • supports up to 42x 12A_7 preamp tubes without octals
  • DC stand-off for heater supply (linkable option)
  • regulated ±12Vdc-175mA auxiliary supply
  • optimized ground tie to chassis

The paralleled main filter cap positions provide ample ripple filtering and long life. Output filtering is also much higher than typically found in guitar amps. This low-noise PSUs can be used to support large numbers of preamp tubes, such as for a mixer or multi-channel active cross-over. In such an application, PSU-50 will support 42 12A_7 tubes.

The London Power 6V/12V heater configuration allows the actual heater wiring to be small-gauge wire, typically #20 or #22. Each of the four 6V heaters has its own wiring connection on PSU-50. A DC-stand-off is provided for a 30db reduction of heater noise.

The bias supply is a typical cascaded RC filter following a full bridge. Proper bias supplies are built using separate windings, as all London Power PTs have.

The auxiliary +/-12Vdc supply provides active regulation of both polarities, supporting op-amps and other solid-state devices, and switching circuitry.

PSU-50 is optimized for use with London Power's PTs, which have dual primaries, plate and bias windings that use a full bridge rectifier (not a half-bridge), CTed auxiliary and the 6V/12V heater winding.

Doubled output wiring blocks are provided to facilitate connection of multiple power amps, preamps and auxiliary circuits. All wiring should be #22 twisted as appropriate. Transformer leads should be #18 or smaller.

Extra fuse blocks are recommended, as it is highly beneficial to protect every secondary and also to protect each output stage. Use only slow-blow fuses around the power transformer and fast-blow types for output transformers.

PSU-50's pcb measures 6" x 3.5" a 2"H (155 x 89 x 51mm)

PSU-50's PT size: 5.6"D x 2.5"H (140 x 65mm)

PSU-50: Printed circuit board plus components plus 50W toroidal PT

Kit requires assembly If you would like this kit pre-assembled, add PSU-BLT to have the PCB pre-assembled,. The transformer fly-leads will NOT be attached to the boards. The assembled boards are bulkier than the loose parts, so shipping is slightly higher.

About London Power

London Power was founded in 1990 by Kevin O'Connor, after two decades of research into innovative audio amplification techniques. Kevin is an audio designer, author and speaker, known for his proprietary methodology called Power Scaling, and for his eleven books on audio subjects. Whether you seek amps, kits or information, you'll find useful answers here on not just the "how" but the "why" of audio amplifier design. Please enjoy the information on this site, and don't hesitate to contact us with questions.

Contact Us

(807) 473-0952
11 am - 6 pm, M-F
PO Box 10012, Thunder Bay, ON P7B 6T6 CANADA